303® Touchless Sealant
- Provides superior water beading
- Protects against paint fading
- Lasts up to 2x longer than traditional wax
- Spray on and rinse off
- Works on windshields and wheels
- Use on glass and paint for a deep, clean shine
Have you had trouble finding time to wax your car thoroughly? 303® Touchless Sealant will save you hours! This Si02 formula is an entirely TOUCHLESS and quicker alternative to waxing your vehicle. Simply spray on, and rinse off – it’s that easy! It only takes minutes to get that same water beading protection you get from a full wax, saving you hours spent in the garage. It’s also great for those looking to prolong the time between waxes or ceramic coatings. Safe for clear coat, gel coat, fiberglass, plastics, windshields, and wheels too!
DIRECTIONS:
Wash your car out of direct sunlight when the vehicle’s surface is cooled. While the exterior is still wet, spray a small amount of product evenly, treating one section of the car at a time. After spraying a light mist, immediately rinse the section off with water. You will see water beading on the surface, indicating that it is now protected. Repeat steps on all areas of the vehicle, and then dry thoroughly with a waffle weave drying towel or microfiber towel.
32oz – SKU 30394CSR
1gal – SKU 30399
Magic in a bottle! We incorporated and modified SiO2 chemistry, which is basically liquefied glass. We added a hydrophobic component to aid in water repellency and durability. The synergy of the chemistry inside the bottle allows it to bond to all exterior surfaces!
This product can be applied to all vehicle exterior surfaces. It is safe and effective on; paint, clear coat, wheels, glass, plastics, fiberglass, gel-coat, aluminum, hard plexiglass and more!
Wash your car out of direct sunlight while surface is cool. While surface is still wet and out of direct sunlight, spray a small amount of product evenly across surface, treating one section of vehicle at a time. Only a light mist of product is needed. Immediately rinse section off. You will see water beading on surface, meaning it is now protected. Repeat steps on all sections of vehicle, and then dry thoroughly with a waffle weave drying towel or microfiber towel. Make sure to rinse product off each section of vehicle thoroughly immediately after applying product – do not let dry on surface, as water spots may occur. Water spots and streaks can also occur if too much product is used, and not rinsed off thoroughly.
Water spots and streaks can occur if the product is used on a hot surface, so make sure your vehicle is cool, wet and out of direct sunlight when applying this product. If you experience spots or streaks due to using it on a hot surface, you will need to rinse the surface again, and then also use a microfiber towel to buff these off.
Spots and streaks can also occur if too much product is sprayed on, and not rinsed off thoroughly or quickly after applying. If spots occur due to this reason, they can easily be removed simply by rinsing surface off again.
Also, make sure you dry your vehicle like you normally would (drying towel, etc.) after applying product and rinsing off. Letting the vehicle air dry can also cause water spots to form.
Yes, it can be. This product can be used on top of other paint protection products or as additional layers on top of itself. In general, we recommend using the longest lasting product as the base coat when layering. The layers on top of your base coat will only last as long as it does.
Yes, so long as the surface is clean, wet, and cool to the touch when applied.
Up to 6 months.
No, this product contains ceramic coating properties, but is not exclusively ceramic.
303 Touchless Sealant has ceramic properties, but is much easier to apply. Ceramic Coatings last longer, but require much more prep and are more expensive.
Durability. Carnauba Wax products tend to last 3 months or less, our product lasts up to 6 months. Our product is not a wax – it is a synthetic sealant, whereas Carnauba is a natural product.
Yes. This product can be used after every wash if desired, but the product must still be water activated (rinsed off first) to function as designed.
Yes, it is safe and effective on gel coat and fiberglass. This product is also Marine safe.
Yes, it will not damage painted surfaces.
Yes, it will help deepen the finish.
